Talk to Us

Config Kit

Configure And Verify Radios Before Mission Deployment

Config Kit is a ruggedized, closed-loop tool for over-the-cable radio configuration and secure waveform analysis. Test, load, and verify before anything leaves the facility.

Schedule a Demo View All Products

THE PROBLEM

Configuring Radios In The Field Is Slow, Risky, And Hard To Repeat

01

Configuring and testing radios over the air risks detection and mission compromise.

02

Untested hardware and waveforms fail in theater, where a failure costs the most.

03

Setting up devices one at a time leaves a fleet inconsistent and slows deployment.

THE SOLUTION

Test And Configure Everything Before It Leaves The Facility

01

Over-the-cable testing verifies configuration without over-the-air exposure.

02

Pre-mission checkout confirms hardware and waveforms work before deployment.

03

Standardized setup brings every device to the same baseline.

04

An intuitive GUI cuts configuration from days to minutes.

How It Works

A Closed-Loop Tool For Secure, Over-The-Cable Radio Configuration

01

Closed-loop, over-the-cable operation

Config Kit tests and configures radios through a sealed cable connection, so nothing goes over the air. It works with both recorded and live RF, which means operators can verify function without broadcasting a signal.

Key Capabilities

  • Closed-loop over-the-cable path
  • Recorded and live RF environments
  • No over-the-air exposure
02

Pre-mission hardware checkout

Confirm a radio powers up, configures, and transmits correctly before it deploys. Catching a hardware or transmit fault in a secure facility is a lot cheaper than discovering it at a forward position.

Key Capabilities

  • Pre-mission hardware checkout
  • Transmit verification without OTA exposure
  • Problems caught before deployment
03

Local waveform loading and verification

Load the waveforms a mission needs and verify them locally, confirming the selected waveforms will function as expected before execution.

Key Capabilities

  • Locally load selected waveforms
  • Verify hardware and software installations
  • Confirm waveforms function as expected
04

Testing against recorded threat environments

Rehearse a radio’s response against captured threat RF without ever transmitting, then analyze the waveform’s behavior across the transmit and receive chains.

Key Capabilities

  • Test against recorded threat environments
  • No over-the-air exposure
  • Waveform environmental analysis on Tx and Rx chains
05

Fleet standardization

Bring every device to the same configuration baseline instead of hand-tuning each one. Standard setup across the fleet means fewer surprises in the field.

Key Capabilities

  • Standardize hardware setup across devices
  • Repeatable configuration
  • Consistent baseline across the fleet
06

Intuitive GUI control

Configure device software through a graphical interface built for speed, not for specialists. This is what takes hardware configuration from days down to minutes.

Key Capabilities

  • Intuitive graphical user interface
  • Simple device software configuration
  • Setup in minutes, not days

01

IP65-rated ruggedized hardware

02

Software-defined radio (SDR) compliant

03

Kubernetes-based architecture

04

COTS-based design for flexibility

FAQ

Common Questions About Pre-Mission Radio Configuration

What is Config Kit and what does it do?
How does Config Kit reduce hardware configuration time from days to minutes?
What is over-the-cable testing and why does it matter?
How does Config Kit reduce mission risk?
Can Config Kit test waveforms against threat environments?
How does Config Kit standardize configuration across multiple devices?
What hardware does Config Kit include?
Which radios and systems does Config Kit work with?
Who uses Config Kit?

Config Kit is a ruggedized, closed-loop, over-the-cable tool for pre-mission radio configuration and secure waveform analysis. Operators use it to load waveforms, verify hardware and software installations, and test transmit function before deployment — in both recorded and live RF environments. Because it runs through a sealed cable path instead of over the air, Config Kit confirms a radio is mission-ready without generating a detectable signal. It pairs a ruggedized control tablet with an SDR test device on a COTS-based, Kubernetes-based architecture.

Config Kit reduces hardware configuration time from days to minutes by replacing manual, one-at-a-time field setup with a guided over-the-cable workflow and an intuitive graphical interface (GUI). Operators load waveforms, verify hardware and software installations, and check transmit function locally, then apply the same configuration baseline across multiple devices at once. Standardizing setup this way removes the repeated hand-tuning and over-the-air troubleshooting that traditionally stretch radio configuration across days.

Over-the-cable testing runs radio configuration and verification through a sealed cable connection in a closed loop, rather than transmitting over the air. It matters because over-the-air testing can expose a unit’s position or intent and risk mission compromise. Config Kit uses over-the-cable testing to verify hardware, load waveforms, and confirm transmit function in a secure environment with zero over-the-air exposure, so the radio is proven before it ever radiates in theater.

Config Kit reduces mission risk by moving radio testing and configuration out of the field and into a secure facility before deployment. Operators run pre-mission hardware checkout, confirm selected waveforms function as expected, and verify transmit — all over the cable, with no over-the-air exposure. Catching a hardware or configuration fault in a controlled environment, instead of at a forward position, keeps untested equipment out of the mission and removes a common source of field failure.

Yes. Config Kit tests waveforms against recorded threat environments with no over-the-air exposure, letting operators see how a configuration behaves against captured RF conditions before deployment. It also performs waveform environmental analysis across the transmit (Tx) and receive (Rx) chains, so teams characterize performance in a secure setting rather than discovering problems live. This lets crews rehearse radio behavior against realistic conditions ahead of a mission.

Config Kit standardizes configuration by applying the same known-good baseline across multiple devices instead of setting up each radio individually. Operators load waveforms and verify installations once, then repeat that exact configuration across every unit in a fleet. This repeatable process reduces human error and ensures each radio ships with an identical, verified setup — which matters when teams field many devices for the same operation and need them to behave the same way.

Config Kit includes a ruggedized control tablet paired with an SDR test device for over-the-cable radio configuration. The hardware is IP65-rated, software-defined radio (SDR) compliant, and built on a COTS-based, Kubernetes-based architecture. Operators drive configuration through the tablet’s graphical interface, connecting to the device under test over the cable for closed-loop verification. The COTS baseline keeps the kit adaptable as new radios and waveforms are added.

Config Kit is software-defined radio (SDR) compliant and configures SDR-based devices, making it a fit for Beacon tactical radios and digital ground systems that need waveforms and configurations verified before deployment. Operators load and verify waveforms, confirm hardware and software installations, and standardize setup across the devices they field, all over the cable in a secure environment. Because the kit is COTS-based, its supported-device coverage can expand as new radios and waveforms are added.

Config Kit supports military and government operators who need to verify software-defined radios and tactical hardware before deployment. Teams operating in contested or sensitive environments use over-the-cable configuration to prepare equipment without over-the-air exposure, standardize large device fleets, and reduce field failures from untested equipment. It fits mission planning and pre-deployment workflows where radios must be proven before they leave a secure facility.

Ready To Configure And Verify Before You Deploy?

Whether you’re preparing a single radio or standardizing an entire fleet, Config Kit lets you test, load, and verify over the cable, before the mission.

Schedule a Demo View All Products

C3 software from orbit to the tactical edge. Built by operators, deployed across the most demanding national-security missions.

Talk to Us

Auria | Copyright 2026 | All rights reserved

Mission-ready integration